Compared

RS485 Modbus to LoRaWAN Converters Compared: MacSync LX1 vs Dragino RS485-LN vs Milesight UC100 vs RAK7431

Four ways to put an existing Modbus energy meter, flow meter, drive or PLC on LoRaWAN, for buyers weighing an alternative to the Dragino RS485-LN, the Milesight UC100 or the RAK7431. Two are DC-powered bridges for inside a panel, one maker offers a mains bridge and a separate battery node, and one is a single design supplied either on a battery or on 9–36 V DC in an outdoor housing.

Macnman product on this page: MacSync LX1

Side by side

The published figures

Every value is as each manufacturer publishes it, checked on 11 October 2026. Where a page does not state a figure, the cell says so.

CompareMacnman MacSync LX1Dragino RS485-LN / RS485-LBMilesight UC100RAKwireless RAK7431
Modbus roleModbus RTU master · function codes 03, 04, 06 and 16RS485 with Modbus support · quick command for function codes 01 to 04Modbus RTU and transparent passthroughPolling, transparent and packet modes
Devices and readsSeveral slaves on one bus, slave ID 1–247 · 1–125 registers per groupRS485-LN: up to 32 RS485 devices · 15 commands per samplingUp to 32 Modbus RTU devices · up to 64 registersUp to 16 RS485 devices · up to 32 polling instructions
Baud rate1,200–115,200 bpsUp to 115,200 bps1,200–115,200 bps9,600–115,200 bps
Other inputsTwo switchable channels for 4–20 mA, 0–10 V or digital, in place of RS485RS485-LB: UART, I²C, 1-Wire and one digital pin1 × RS4851 × RS485
Power19 Ah battery variant, or 9–36 V DC variantRS485-LN: 7–24 V DC, no battery · RS485-LB: 8,500 mAh Li-SOCl₂ cell5–24 V DC or USB-C 5 V; no battery listed8–48 V DC or Micro USB 5 V; no battery listed
Powers the connected deviceYes: selectable output level, 0–2,000 ms warm-upRS485-LB: 3.3 V and 5 V outputs; RS485W-LB adds 12 VNot on the page checkedYes: output follows the 8–48 V DC input
Reporting and alarmsPeriodic, threshold trigger (two triggers, each with minimum and maximum) and sampling modesNot on the pages checked16 IF-THEN commands · threshold and change alarmsNot on the page checked
LoRaWANv1.0.4 · Class A, Class C via the app · OTAAv1.0.3 · RS485-LN Class A and C, default C · RS485-LB Class AClass C · OTAA or ABP; version not on the page checkedv1.0.3 · Class A, B and C
BandsIN865 · RU864 · EU868 · US915 · AU915CN470 · EU433 · KR920 · US915 · EU868 · AS923 · AU915 · IN865 · RU864CN470 · IN865 · EU868 · RU864 · US915 · AU915 · KR920 · AS923IN865 · RU864 · EU868 · US915 · AU915 · KR920, by model
EnclosureIP65, IP67 optional · −40 to +80 °CRS485-LB: IP67 · −40 to +85 °C · RS485-LN: not on the page checkedIP30 · −20 to +60 °CIP31 · −30 to +65 °C
ConfigurationMaya app over Bluetooth · downlinkAT commands · downlink · RS485-LB adds BluetoothUSB-C · downlinkAT commands over Micro USB
ManufacturerMacnman, Pune, India · WPC compliantDragino, Shenzhen, ChinaMilesight, Xiamen, ChinaRAKwireless, Shenzhen, China

Figures for the other products are taken from their manufacturers' published datasheets and product pages, checked on 11 October 2026, and may change; check the linked sources before you order. Dragino, Milesight and RAKwireless are trademarks of their respective owners.

Where each fits

What the table means for your site

Where the MacSync LX1 fits

Energy meters, flow meters and transmitters outdoors or with no supply nearby: water networks, pump houses, solar plants and utility assets, where a 19 Ah battery variant in an IP65 housing matters. The 9–36 V DC variant serves panels and can run in Class C for prompt register writes. Registers are set up in the Maya app with no AT commands, the same hardware reads two analog channels in place of RS485, and a MacTalk version links devices with no gateway. Indian manufacture, WPC compliance and support from Pune come with it.

Where the Dragino RS485-LN and RS485-LB fit

The RS485-LN is a DC-powered bridge that runs Class C by default, for a powered device that needs quick downlinks. The RS485-LB is the battery node of the family, IP67 with an 8,500 mAh cell and a UART as well as RS485. Both are configured by AT commands and downlink; the RS485-LB adds Bluetooth.

Where the Milesight UC100 fits

An indoor panel with a DC supply and many Modbus devices on one line: up to 32 devices, Class C, and 16 IF-THEN commands with threshold and change alarms. Its IP30 housing is for inside a cabinet.

Where the RAK7431 fits

A cabinet with an 8–48 V DC supply, where the bridge can pass that supply on to the RS485 device. It supports Class A, B and C, up to 16 devices and 32 polling instructions, and is configured with AT commands over Micro USB. Its housing is IP31.

Get a quote

Need a quote for the MacSync LX1?

Tell us how many you need and where they are going. A product engineer replies within one working day with availability, lead time and the right variant, and will tell you honestly if another unit fits your site better.

  • Reply within one working day
  • Designed and built in Pune, India
  • WPC compliant, RoHS conformant

Questions

Choosing between them

Yes, for the same job: it is a Modbus RTU master on RS485 that reports registers over LoRaWAN, with function codes 03, 04, 06 and 16 and baud rates from 1,200 to 115,200 bps. The differences are around the Modbus core. The RS485-LN and the UC100 need a DC supply and sit inside a panel, while the MacSync LX1 is supplied on a 19 Ah battery or on 9–36 V DC in an IP65 housing, is configured from a phone app with no AT commands, and is made in India for IN865.

The MacSync LX1 battery variant carries a 19 Ah cell and the Dragino RS485-LB an 8,500 mAh cell. The Dragino RS485-LN, the Milesight UC100 and the RAK7431 need a DC supply. Macnman’s reference figure for the MacSync LX1 is about 8 years at one uplink an hour on SF7; battery life shortens with faster reporting, a higher spreading factor or a sensor that the converter has to power, so ask for an estimate for your registers and interval.

The MacSync LX1 is IP65 with an IP67 option and is rated from −40 to +80 °C; the Dragino RS485-LB is IP67 and rated from −40 to +85 °C. The Milesight UC100 is IP30 and the RAK7431 is IP31, so both belong inside a panel or cabinet.

The MacSync LX1 has a sensor power output with a selectable level and a warm-up time from 0 to 2,000 ms, so a sensor is powered only while it is read. The Dragino RS485-LB lists 3.3 V and 5 V outputs, and the RAK7431 passes its 8–48 V DC input through to the device. The Milesight UC100 page does not list a sensor supply.

Not on the MacSync LX1: slave ID, register address, function code and data type are entered in the Maya app over Bluetooth, and can be changed later by downlink. The Dragino converters and the RAK7431 are configured with AT commands, and the Milesight UC100 over USB-C or by downlink.

The MacSync LX1 reads two switchable channels, each set to 4–20 mA, 0–10 V or digital, in place of RS485. For relay outputs alongside Modbus, look at an IO controller: the MacSet LX1 with two 16 A relays is compared with the Milesight UC300 and the Dragino LT-22222-L on the LoRaWAN IO controller comparison page.

All four list IN865. The MacSync LX1 is designed and manufactured in Pune, ships on IN865 as standard and has a WPC compliant radio; the other three are imported.

Got an IoT idea?

Let’s bring it to life!

flag image

WPC compliant · RoHS · a product engineer replies within one working day

Let‘s Make it Easy

Reach Out Now

Icon

Contact to Sales

Talk to our friendly team

chat@macnman.com
Icon

Call Us

24 X 7 Always On

+91 7972856163
Icon

Contact to Support

We are here to help

support@macnman.com
Icon

Visit Us

Visit our office HQ

View on Google Map

Socials

Use of this website and purchase of Macnman products are subject to our Terms and Conditions.